Laboratory for Building Materials and Structure Diagnostics

Institute of Civil Engineering©
Laboratory for Building Materials and Structure Diagnostics©
Blick in das Labor

After the establishment of the Institute for Civil Engineering in 2018, the laboratory was set up within just a few years. Today, there is a laboratory equipped with state-of-the-art testing technology where students can learn the basic material testing procedures, try out several diagnostic methods and conduct experimental investigations as part of their final theses or student projects. Furthermore, the laboratory offers the possibility to perform material tests and structural diagnostic examinations for external clients.

The laboratory is temporarily housed at two locations. On the campus, the construction materials technology area is located in building C35. The structural diagnostic facility with non-destructive testing (NDT) specimens is located in building F10 at the "Seefischmarkt".

  • Building Materials
  • Material Testing
  • Construction Diagnostics
  • Non-Destructive Testing (NDT)
  • Structural Health Monitoring
  • Mechanical Testing of Material Properties
  • Non-Destructive (NDT) and Minimal Invasive Testing of Structures and Materials
  • Development and Testing of NDT-Methods
  • Hydraulic Testing System for determining mechanical parameters consiting of:
    • Compressive strength test frame 5000 kN, e.g. for concrete, wood, bricks
    • Flexural strength test frame 300 kN, e.g. for concrete, fibre reinforced concrete as 3- or 4-point bending test
    • Combined compressive and flexural strength test frame (300kN, 10 kN), e.g.for cement, mortar and gypsum test samples as well as lightweight and aerated concrete
    • Equipment for determining the Young´s Modulus and the indirect tensile strength (splitting) of concrete
  • Water Impermeability testing setup, e.g. for concrete
  • Wet Concrete and Mortar testing (e.g. flow consistency, air entrainment meter, Hägermann-Flow Table)
  • Cement Testing (e.g. Vicat, Le Chatelier, Blaine)
  • Paddle Mixers for Concrete and Mortar Mixers
  • Specimen Storage
    • Humidity cabinet, e.g. for mortar specimens
    • Temperature controlled water storage for concrete and mortar specimens
    • Drying cabinet, e.g. for small sized specimens and testing materials
    • Climate chamber with CO2 control for carbonation tests, e.g. on cementitious materials
  • Ultrasonic Device for determining the dynamic modulus, e.g. of concrete
  • RCM Device (Rapid Chloride Migration): Determination of the chloride migration coefficient on concrete drill cores
  • Potentiostats for electrochemical (corrosion) tests
  • Potential Mapping: minimal-invasive localisation of areas with a high corrosion risk on reinforced concrete structures
  • Resistivity Meter: non-destructively on the structure or destructively in the laboratory (e.g. drill core)
  • Cover Meters: non-destructive localisation of reinforcement bars, determination of concrete cover depths and minimal-invasive determination of rebar diameters in concrete structures
  • Radar Scanners: non-destructive localisation of reinforcement bars or installations or determination of structure dimensions
  • Ultrasound Scanners, Impact-Echo: e.g. non-destructive determination of structure dimensions and localisation of hollow areas by pulse transmission or echo
  • Microwave and Capacitive Sensors: non-destructive determination of moisture in poreous building materials
  • Rebound Hammer: non-destructive or minimal-invasive determination of concrete compressive strength at the structure (R- and Q-Values)
  • Tear off Test Device: for determining the surface tensile strength or adhesive pull strength
  • Torrent Permeability Tester: non-destructive determination of the gas-permeability of concrete
  • Bore Dust Extraction Device: e.g. for extracting concrete samples in order to determine the chloride content
  • Concrete Core Drill
  • Crack Monitoring: electronic or analog recording of crack widths. Also crack magnifier, scales, etc.
  • Endoscope: e.g. for assessing hollow areas and bore holes
  • Climate Sensors: e.g. air and structure temperature, rel. air humidity

Directions

  • Laboratory "Seefischmarkt"
    Building 10a (F10)
    (Zentrum für maritime Technologie und Seefischmarkt)
    Wischhofstr. 1-3
    24148 Kiel
    Anfahrt Seefischmarkt (Google)
  • Office (Campus)
    Building C34
    Moorblöcken 12
    24149 Kiel
  • Mail and Package Delivery (Campus)
    Kiel University of Applied Sciences
    Faculty of Media and Civil Engineering
    Laboratory for Building Materials and Structure Diagnostics
    Grenzstr. 3
    24149 Kiel